Martin MX SERIES Manuale Utente

MX-1user manual

10 Data connection MX-1 user manualDATA CONNECTION5This section describes how to connect fixtures to a controller. RECOMMENDED CABLEA reliable data co

MX-1 user manual Data connection 11To connect the data link1 Connect a data cable to the controller’s data output. If the controller has a 5-pin outpu

12 Stand-alone operation MX-1 user manualSTAND-ALONE OPERATION6The MX-1 may be operated without a controller in stand-alone mode. It may beoperated as

MX-1 user manual Stand-alone operation 13To set the masterImportant! Set only 1 fixture as master (DIP-switch pin 2 and 10 ON). 1 Set DIP-switch pins

14 MC-1 operation MX-1 user manualMC-1 OPERATION7All new MX-1s and older MX-1s with CPU firmware v 1.7 or higher are fullycompatible with the Martin M

MX-1 user manual DMX operation 15DMX OPERATION8 DMX MODESThe MX-1 has 3 DMX modes to choose from: a 1-channel mode that providescontrol of the built-i

16 DMX operation MX-1 user manualFind the address in the table below. Read the settings for pins 1 - 5 to the left andread the settings for pins 6 - 9

MX-1 user manual DMX operation 17 1-CHANNEL DMX OPERATIONThe functions shown in the following table are available in 1-channel mode.When a “stand-alon

18 Basic service MX-1 user manualBASIC SERVICE9The MX-1 requires simple routine maintenance. The maintenance scheduledepends heavily on the operating

MX-1 user manual Basic service 19To clean the fan and air ventsTo maintain adequate cooling, dust must be cleaned from the fan and air ventsperiodical

1 focus lens2 cover screws3 air vent4 mirror assembly5 pan/tilt arm6 safety cable holes7 mounting bracket8 air vents9 AC input & main fuse10 DIP-s

20 Troubleshooting MX-1 user manualTROUBLESHOOTING10Problem Probable cause(s) RemedyOne or more of the fixtures is completely dead.No power to fixture

MX-1 user manual DMX protocol 21DMX PROTOCOLA*Extended DMX mode (jumper on PL 118)Channel Value Percent Function10 - 45 - 154155 - 169170 - 229230 - 2

42white25 50 75 100 125 150 175 200 225 250B/Ofast slowautoMX-1 DMX Protocol StrobeDimmer87516Stand-alonenot usedTilt10 20 30 40 50 60 70 80 9025 50 7

MX-1 user manual Specifications 23SPECIFICATIONSBPHYSICAL• Size (L x W x H)... 537 x 269 x 263 mm (21.1 x 10.6 x 10.4 in)•

MX-1 user manual 3Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Safety precautions . . . . . . . . .

4 Introduction MX-1 user manualINTRODUCTION1Thank you for selecting the Martin MX-1. The MX-1 is an automated profilespotlight that employs a 250 watt

MX-1 user manual Introduction 5• Never place flammable materials anywhere near the fixture.• Never illuminate surfaces within 0.3 meters (12 inches) o

6 Lamp MX-1 user manualLAMP2The MX-1 comes from the factory with a Philips 500 hour lamp installed. This a24V, 250W ELC halogen lamp. A high-output 50

MX-1 user manual AC power connection 7AC POWER CONNECTION3Warning! For protection from dangerous electric shock, the fixture must be grounded (earthe

8 AC power connection MX-1 user manualTo install a plug on the mains leadThe fixture’s mains lead must be fitted with a grounding-type cord cap thatfi

MX-1 user manual Installation 9INSTALLATION4The MX-1 can be fastened directly to a suitable surface or to a rigging clamp bymeans of its adjustable mo